TS Machinery - Specialize In Fabricating Shot And Sand Blasting Equipment
For Surface Treatment Industry More Than 10 Years.
|Place of Origin:||China|
|Minimum Order Quantity:||1 Set|
|Delivery Time:||15-20 work day|
|Supply Ability:||10 Sets per month|
|Working Efficiency:||0.6-1.2t/h||Blast Wheel:||7.5kw|
|Filter Type:||2pcs Cartridge, Diameter 350mm X H660mm||Warranty:||1 Year|
tumblast shot blasting machine,
abrasive blasting equipment
Tumble Belt Shot Blast Machine Q326 With φ600mm Drum Diameter 150L Volume
1. Adopts large volume of centrifugal blast wheel, with high blasting speed, can significantly improve the cleaning efficiency, obtain the good cleaning quality.
2. It adopts wear-resistant rubber to reduce the damage of workpiece and noise of equipment.
3. The blasting area is protected by high chromium wear-resistant plate, compare to rubber plate used before, the service life is greatly improved, and the appearance is nice, easy to replace, it is the most popular way to protect the blasting cabinet.
4. The utility model has the advantages of compact structure, high production efficiency, good cleaning result, safe and reliable operation and stable performance, easy to operate.
Add the required number of workpieces in the clean room, start the machine, belt begins to rotate, the workpiece is cleaned by high speed continuous blasting shots, the shots and dust fall into bottom cabinet through the holes of belt after blasted, big particles will leave on wire mesh, the small ones will be transported to separator, dust will be sucked into dust collector, the good shots will fall into abrasive hopper and ready for recycle using.
Tumble belt shot blast machine is suitable for:
casting tube and elbows
other small fabricated metal work pieces
|1||Max Weight of Single Part||10 kg|
|4||Surface Cleaning Requirement||GB8923-88 A-B Sa2.5|
Blast Volume:180 kg/min
|7||Abrasive Recommend||Φ0.4～Φ1.2mm(steel shot and steel cut wire)|
|8||Abrasive Fist Feed||≈0.1T|
Air Speed:4～5 m/s
|12||Tumble Belt System||1set||Drum Diameter:Φ600mm|
|14||Noise Level||≤85 dB|
|15||Filter Type||2pcs Cartridge, diameter 350mm x H660mm|
|16||Dust Emission||≤80 mg/m³|
|17||Process Air Volume||Total Air Volume:2000m³/h
|21||Total Power||about 12.0kw(include dust collector 1.5kw)|
This is a small cleaning equipment, mainly composed by the cabinet, blasting system, abrasive recycle system, dust collector, electrical system and etc.
a. Blasting Cabinet(Longer Serive Time)
Inside the cabinet, there equips with wearing-resistant rubber to carry the products rotate. The shell is protected by special wear-resistant alloy shield mounted on end sides of belt, which is made by high chromium iron casting.
b. TS Blast Wheel (High Efficiency + Longer Service time)
It is key part of shot blasting machine, consists of blades, control cage, wheel disc, impeller, protective linings, wheel house, feeding pipe, special motor and etc.
c. Door (Good Sealing)
It is single swing door hanging with wear-resistant rubber to protect the door and sealing.
d. Elevator + Air Wash Separator
(with advanced design, dust and abrasive can be separated up to 99.5%)
To ensure conveyor belt not slip when machine is working, the pulley was made into a squirrel cage, that increase friction between belt and pulley, reduce the press-tightening force, extend belt service life. While elevator is equipped with a tension device, belt can be tensed by adjusting the upper bolt when it loose.
e. Cartridge Dust Collector(More Easier to Clean)
Pulse-jet Air Clean System
The dust collector has a push button to “pulse” the cartridges with a jet of compressed air between blast cycle to purge the filter. Upgrade option, the part can be programmed in PLC.
f. Electrical Control Panel (More Safty)
Qualified electronic components from famous company, such as Schneider, Chint or other Equivalent brand;
With Emergency Button; Control Voltage 24V;
Interlock System: there is a limit switch above the door, only after the door closed, can the blasting wheel be started.
Before and After
Why choose tumble belt shot blasting machine from TS Blasting?
Protective plate in blasting zone SP Mn13
Low chromium casting
Service life of Mn13 is 8000-10000, Low chromium casting is 1500-2000h
|2||Equip with 1 sets dust collector with pulse-jet air clean system||Equip with 1 set bag filter or cartridge filter||Bag filter need manual vibration, filter area is small with big occupation, ash removal difficulty|
Electronic brand are Schneider/Chint
Electronic brand is Delixi
Choosing big brand Electrical components, with high stability of equipment
Top sealing uses a total of 5 layer protection (sealing brush and sealing rubber)
Top seal 2 layer of protection
5 layer seals are more effective in preventing steel shots and dust escape out
Equip with safety protection such as ladder, guardrail and etc.
Ladder and guardrails to ensure the safety of staff for repair and maintain purpose.
Equip with sealing device and screen mesh at each transmission bearing
Bearing equipped with sealing device is not easy to break down, and protect the transmission parts and motor.
Dust-removing fan outlet equipped with silencer
Silencers can effectively reduce noise decibels and protect the health of workers.
Contact Person: tina